Direct answer
For the NETGEAR Nighthawk RAX120 router, guest isolation is usually intentional; internet and local discovery are separate permissions. First, test internet and a local printer/cast target from one guest client.
What this covers
- NETGEAR Nighthawk RAX120 router (RAX120)
- NETGEAR router/mesh; modem integration, Wi-Fi generation, Armor, guest and Ethernet ports vary.
- The specific fault this record addresses: guest network cannot reach devices, cast or print
What it does not cover
- ×The same symptom on a different NETGEAR product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
The guest network is disabled, hidden, or on a band the guest device lacks
What separates it Guests cannot see or join the guest SSID at all.
How to confirm Confirm the guest network is enabled and broadcasting, and that a 2.4 GHz-only guest device is offered a 2.4 GHz guest SSID.
- 2
Client isolation is (correctly) blocking access to a local device
What separates it A guest is on the network but cannot reach the printer, the Chromecast or a shared drive.
How to confirm This is guest isolation doing its job — it walls guests off from your LAN; put the device the guest needs on the main network, or use a router option that specifically allows a shared device, rather than disabling isolation wholesale.
- 3
A captive portal or usage schedule is interfering
What separates it Guests connect but must pass a portal that fails, or the guest network turns off on a schedule.
How to confirm Check the guest portal and any time schedule; a portal that does not complete or a schedule that has expired blocks access as configured.
- 4
The guest password or limit is the block
What separates it Guests are refused with a password error, or a device/time limit has been reached.
How to confirm Re-share the correct guest password and check any client or time limit on the guest network.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- Whether guests cannot join at all, or join but cannot reach a specific device.
- Whether client isolation is on (it usually should be) and what device the guest needs.
- Whether a captive portal, schedule or device limit is configured on the guest network.
Confirm the guest SSID is enabled, broadcasting and on a band guests can use
ReversibleOffer 2.4 GHz for simple guest devices.
Decide whether isolation should block the device the guest wants
ReversibleIsolation is protective; move the needed device to the main network instead of turning isolation off.
Check the captive portal, schedule and any device/time limit
ReversibleThese block access exactly as configured when they misfire or expire.
Re-share the correct password and confirm a guest can browse
ReversibleVerifies join and internet access without exposing the LAN.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- RAX120. NETGEAR router/mesh; modem integration, Wi-Fi generation, Armor, guest and Ethernet ports vary.
- Wi-Fi 6 router (high-end, single unit, dual-band)
- A high-end Wi-Fi 6 (AX) router with 2.4/5 GHz (no 6 GHz — that is 6E/7). Wi-Fi 6 speeds need Wi-Fi 6 clients; older devices connect at their generation normally.
- Single router coverage
- Covers a limited area as a single unit; large homes may need mesh/extenders or central placement. A weak room is coverage, not a fault.
- Managed by app or web
- Nighthawk app or web admin. It has no 6 GHz band, so 'no 6 GHz' is the hardware generation, not a fault.
- Symptom boundary
- This record covers NETGEAR Nighthawk RAX120 router when it guest network cannot reach devices, cast or print. A different symptom on the same hardware, or this symptom on a different NETGEAR product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Do not disable guest isolation to solve one access problem — that removes the whole point of a guest network and exposes your main devices. Allow one specific shared device instead where the router supports it.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. NETGEAR Support publishes this as "Home networking support". Official NETGEAR router, Orbi, modem, switch and extender support. What that article does not carry is the model boundary — it is written for a product line, and RAX120 is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
Does the Netgear RAX120 have a 6 GHz band?+
No — the RAX120 is a Wi-Fi 6 (AX) router with 2.4 and 5 GHz bands only. The 6 GHz band came with Wi-Fi 6E (the RAXE models) and Wi-Fi 7. So there is no 6 GHz network to find on this router, which is its generation rather than a fault. It still delivers strong Wi-Fi 6 performance to compatible devices on the 5 GHz band.
Guests are on the guest Wi-Fi but can't reach my printer.+
That is guest isolation working as designed — it deliberately walls guest devices off from your main network so they cannot see your printer, drives or smart-home gear. Rather than turning isolation off, which defeats the purpose, either put the printer on the main network for the guest to use, or use your router's option to allow one specific shared device across to the guest network if it has one.
Does this answer apply to every NETGEAR model?+
No. It is scoped to RAX120. NETGEAR router/mesh; modem integration, Wi-Fi generation, Armor, guest and Ethernet ports vary.
What should I record before troubleshooting guest network or isolation?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing guest network, isolation. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Do not disable the firewall globally.
Answer for the exact device and software version shown above.