Direct answer
For the Canon Color imageCLASS LBP632Cdw, model capability, driver option, paper size/type and accessory detection must align. First, verify exact model duplex capability and print an internal configuration page.
What this covers
- Canon Color imageCLASS LBP632Cdw (5159C003)
- Canon printer; PIXMA/MegaTank/MAXIFY/imageCLASS ink/toner systems and maintenance paths differ.
- The specific fault this record addresses: will not print or scan two-sided
What it does not cover
- ×The same symptom on a different Canon product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
The binding edge setting is wrong
What separates it Both sides print but alternate pages are upside down.
How to confirm Long-edge and short-edge binding produce different orientations. This is a setting rather than a fault, and it is the most common duplex complaint.
- 2
The paper is too heavy or too light for the duplex path
What separates it Jams only when duplexing, with card or thin paper.
How to confirm The duplex path usually supports a narrower media range than single-sided printing. Check the specification.
- 3
The paper is curling as it passes through
What separates it Jams on the second pass, worse with laser printers and light paper.
How to confirm Heat curls paper, and a curled sheet re-entering the path jams. Fresh, correctly stored paper helps considerably.
- 4
The duplexer is not seated
What separates it Duplex options unavailable, or a jam reported immediately.
How to confirm Reseat the duplex unit fully where it is a removable module.
- 5
The driver does not have duplex enabled
What separates it The option is greyed out in the print dialog.
How to confirm Duplex sometimes has to be enabled in the driver's installed-options settings before it appears.
- 6
The application is overriding the printer setting
What separates it Duplex works from one application and not another.
How to confirm Some applications carry their own duplex setting that overrides the driver default.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- Whether the failure is mechanical, or pages printing correctly but oriented wrongly.
- Which binding edge is selected.
- The paper weight, compared with the duplex path's supported range.
- Whether it fails from every application or only one.
Switch between long-edge and short-edge binding
ReversibleAlternate pages upside down is this setting, not a fault, and it is the most common duplex complaint.
Check the paper weight against the duplex path's supported range
ReversibleThe duplex path usually supports a narrower range than single-sided printing does.
Use fresh, flat, correctly stored paper
ReversibleHeat curls paper on the first pass, and a curled sheet jams as it re-enters.
Reseat the duplex unit and enable duplex in the driver's installed options
ReversibleA greyed-out duplex option is usually this rather than a missing capability.
Test from a second application
ReversibleSome applications override the driver's duplex setting with their own.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- 5159C003. Canon printer; PIXMA/MegaTank/MAXIFY/imageCLASS ink/toner systems and maintenance paths differ.
- Type — COLOR LASER, PRINT-ONLY (no scanner/copier)
- A colour laser printer that is PRINT-ONLY — it has NO scanner, copier or fax (the LBP line is single-function). So scan, copy and ADF symptoms do not apply to it; it only prints. Colour laser uses toner and does not clog from disuse.
- Toner & drum
- Faded print is low/unseated toner; streaks/repeating marks are toner or drum. Fast, low-cost colour printing without scan/copy features.
- Connectivity
- Wi-Fi/Ethernet/USB; 'offline' is usually a network/queue issue.
- Symptom boundary
- This record covers Canon Color imageCLASS LBP632Cdw when it will not print or scan two-sided. A different symptom on the same hardware, or this symptom on a different Canon product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Do not force paper through a duplex path or reach into a laser fuser area before it has cooled.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. Canon publishes this as "Cannot Print Properly with Automatic Duplex Printing". Canon's article for automatic two-sided printing that will not run or produces wrong output - paper size, type and driver setting. Probed 2026-08-21: title-verified. What that article does not carry is the model boundary — it is written for a product line, and 5159C003 is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
How do I scan or copy on my Canon imageCLASS LBP632Cdw?+
You can't — the LBP632Cdw is a print-only colour laser printer with no built-in scanner or copier (the LBP line is single-function). So there is no scan or copy feature to use or troubleshoot on this model. To scan or copy you would need a separate scanner or an all-in-one/multifunction printer (Canon's MF-series). The LBP focuses purely on fast, low-cost colour laser printing.
Double-sided printing comes out with every other page upside down.+
That is the binding edge setting rather than a fault. Long-edge binding flips pages like a book, short-edge binding flips them like a notepad, and choosing the wrong one for your layout gives exactly this result. Switch it in the print dialog and reprint.
Does this answer apply to every Canon model?+
No. It is scoped to 5159C003. Canon printer; PIXMA/MegaTank/MAXIFY/imageCLASS ink/toner systems and maintenance paths differ.
What should I record before troubleshooting duplex or two-sided?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing duplex, two-sided. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Do not force unsupported media through duplex paths.
Answer for the exact device and software version shown above.